3 important tips, Master class + Video

3 important tips, Master class + Video Most of our fellow citizens are sure that having even a little experience in repair work, you can stick wallpaper with high quality and beautifully.

Perhaps this is the case when it comes to straight walls and right angles.

But few apartments, especially the well-known Khrushchevs, can boast of such indicators.

How to properly paste the wallpaper in the corners? Where is it better to start, from which side?


Recommendations of professionals

Questions from the topic "how to glue the wallpaper", perplex amateur masters and sometimes they give rise to doubts about the speedy and successful completion of the undertaken repair.

Without understanding all the intricacies of the gluing workflow, you can ruin the wall covering.

Not too straight corners are found not only in old apartments: they are not uncommon for new buildings. Wall irregularities also often make it difficult to repair quickly and easily. Let's take a look at some recommendations that will help us cope with the task at hand.

3 important tips, Master class + Video 1. Avoid Creases

When gluing wallpaper to the outer corner tabs, you should try to do so in such a way that the wallpaper is as close to the wall as possible.

Professionals do not advise to glue the entire length of the strip at the corner at once. If the joint is not very even (and this is more often the case), then the paper can collect in sloppy folds.

2. Maintain the protrusion

It is not desirable that the wallpaper ends at the very corner. It is advisable to leave a three-centimeter protrusion, which can then be carefully cut off with a knife.

This will achieve a more even pasting. If you purchased heavy and dense wallpaper, then when decorating the walls with them, you should use a plumb line.

3. Remove electrical accessories

Often there are switches or sockets near the joints. Not forgetting to turn off the electricity, remove the outer covers from them.

After that, you can start the process of directly gluing the wallpaper. Then, when the glue dries, circles with a diameter slightly smaller than the casing itself are cut out on the dry canvas with a sharp knife. After completion of work, the fittings are returned to their place

Gluing process


All preparatory work must be done before finishing the corners begins ...

The old wall covering is thoroughly cleaned , all irregularities and defects are removed. To align the joints, you can use special corners made of plastic, which are fixed with putty. Then, using a roller or brush, apply a special primer to the wall.

3 important tips, Master class + Video

Next, select the angle from which we will start working. We prepare a piece of wallpaper of the required size, spread it with glue, if necessary, it covers the piece of the wall for which it is intended.

When using plastic corners, they are also coated with the composition.By smearing the wall, you can go a few centimeters beyond the future sheet.

Sticking the first strip . If the work is carried out from left to right, then the left side of the wallpaper strip is applied in the corner. It must be perfectly aligned along its entire length.

With a clean cloth or a special device (plastic spatula or roller), the coating is smoothed over the entire area, moving gently and gradually, expelling air and removing bubbles. The wall is completely pasted over to the nearest corner.

3 important tips, Master class + Video

How to glue the wallpaper in the inner corners

This type of corner is usually found in rooms. For competent and even pasting, you must adhere to the listed recommendations.

The strip is glued so as to cover, together with the corner, a few centimeters of the adjacent wall (3-4).

It is carefully pressed and smoothed with a clean, lint-free cloth.

3 important tips, Master class + Video Then, on the adjacent wall using a ruler from the upper corner, the width of the canvas is laid down minus the mentioned 3-4 cm This is done in order to stick the next strip in relation to the previous overlap.

By means of a plumb line or level, a line is drawn down along the entire wall, which will serve as a reference point. A strip will have to be glued along it strictly vertically.

Then you can go to the adjacent wall.

As already mentioned, the next strip is glued along the line marked on the wall, overlapping the previous one. Just like everyone else, it is carefully smoothed and pressed, especially at the junction of the walls. Then, using a sharp knife, a ruler and a level, both layers of wallpaper are cut in the corner, unnecessary scraps are removed.

This should be done carefully so as not to accidentally remove the desired piece of wallpaper. Then coat the edges of the canvas with glue, smooth and press.

Take care not to form air bubbles. If you use this technique to finish the corners, you can make the corner joint almost invisible visually.

How to glue wallpaper on the outer corners

Meanwhile, along with the inner ones, in every residential building there are also outer corners. These are, for example, the familiar slopes.

To make it easier and more accurate to paste over them, it is advisable first to level them with plaster.

Unfortunately, this is not possible in every case. Then you will have to apply the overlapping method.

What is the most convenient way to do this?

3 important tips, Master class + Video As when working with internal corners, first a layer of material is glued with an approach to an adjacent wall, at a distance of the previously mentioned 3-4 centimeters.

In order to ensure an even adherence of the wallpaper to surfaces, it is allowed to carefully trim it in several places. When the blade is smoothed, the excess is cut with a razor or sharp knife along the vertical edge, with the exception of a thin edge.

Then a distance equal to the roll width plus five millimeters is measured on the wall with a large ruler or construction tape.Using a plumb line from this point, draw a vertical line down.

We will stick the next strip of wallpaper, focusing on it. When gluing two adjacent strips, a slight overlap will result, which will mask all possible defects formed when cutting the first piece.

How to glue wallpaper with a pattern in the corners

3 important tips, Master class + Video If we have work to do with a coating that has a clear and distinct pattern, it is important to take care that the wallpaper in the corners does not distort the existing pattern.

This is not as difficult as it might seem.

The main thing is not to forget about the need for some overlap. In addition, it is necessary to glue the canvases in such a way that the edge exactly matches the plumb line. Then along the edge of the corner (edge) the second edge is trimmed.

It is quite difficult to prevent the pattern from shifting completely, and slight distortion may occur.

But it will be so insignificant that most likely only you will know about it. Only a careful study of the lines of intersection and connection will allow you to notice it. If you follow all the recommendations for pasting the inner and outer corners, individual sheets of material will lie exactly vertically, and a small distortion of the pattern will not be noticeable.


There are little secrets for wallpapering in the corners.

  • 3 important tips, Master class + Video If the wallpaper you purchased is rather heavy and thick, it is advisable to buy increased strength glue.

    Better that it is transparent.

  • If you prime them well before pasting the walls, the wallpaper will stick to them better. Don't forget about the corners.
  • All procedures for leveling the pasted wallpaper should be carried out before they are completely dry, as it is much easier to move wet cloths.

If you follow all these simple recommendations, then you can qualitatively and beautifully wallpaper the room.

Even if the joints are not too straight, they will nevertheless look neat and beautiful.

The main thing is to be patient and accurate, to do all the activities slowly and carefully. Then the result will delight you!

( 16 marks, average 4 . 5 of 5 )