5 carpentry tricks. Little-known joinery life hacks. Life hack when polishing, do-it-yourself putty

5 carpentry tricks. Little-known joinery life hacks. Life hack when polishing, do-it-yourself putty In this article, we want to tell you what subtleties exist to facilitate carpentry work, as well as 5 carpentry tricks and little-known life hacks , with which you can simplify the creation of any wooden product.

Carpentry craftsmen could probably continue this list indefinitely. With experience, many ideas come with the help of which you can replace many professional tools, if such are not at hand at the right time.

We hope our little carpentry tricks will come in handy in your carpentry workshop.

We offer you a selection of 5 carpentry life hacks for all occasions

  1. Do-it-yourself putty. If you urgently need a putty, and there is nowhere to take it at the moment, then it is quite possible to do it yourself.

    To do this, mix PVA glue with small wood shavings and add a little water.

    When chalk is added to this mass, the mixture will be more plastic. Thanks to this putty, you can not only close the cracks, but also pull off the wood.

  2. 5 carpentry tricks. Little-known joinery life hacks.</p><p> Life hack when polishing, do-it-yourself putty Life hack of sanding with sandpaper. Sanding paper is more commonly used when sanding. It smoothes out sharp edges.

    Generally, the finer the paper grains, the thinner the base will be. This means that paper with a higher degree of grain will tear faster than the grain itself. Whatever this happens, we glue it on the back with adhesive tape. Both reinforced and regular will do. This will make it stronger.

  3. How to avoid the formation of dents on wood. Not a very pleasant phenomenon - the formation of grooves on a wooden product. However, not many people believe that they can be removed. For which we take a regular piece of material, moisten it and shake it off to get rid of excess water. We put this rag on the dent so that moisture would start to get into the pores of the tree.

    Then we take the iron, set it to the maximum value and begin to iron this cloth. Press the iron tightly to the surface, continuing until the cloth is completely dry. It will take quite a long time.

    What will happen in this case: the tree will absorb moisture and begin to distribute and take on its original shape. This process must be repeated until the dents are completely gone.

  4. Life hack when polishing . Typically, sandpaper and polishing paste are used to polish wood surfaces, but it takes a lot of effort and time. Also, dust will adhere to the coating faster than the surface has time to dry. And if you use long-drying products, then even more so. And here an excellent solution would be to use kraft paper folded several times.

    She has strong imaginative qualities and at the same time is not very rude. Such paper can smooth out dust on a dried surface without damaging it.If there is not much dust, then using such a device you can make a perfectly flat surface.

  5. Determination of wood moisture content without a special measuring device. Let's cut off a small piece of wood and weigh it.

    Let's write down the weight of this control piece.

    Then we put it in the oven and dry well at a temperature of one hundred degrees Celsius. Every hour you need to take out this piece and weigh it. As soon as the wood is completely dry, all moisture will come out, its weight will cease to change.

    Then everything is simple - if a dry workpiece weighs thirty-five grams, and before drying it weighed forty-five grams, then it turns out: 45-35 = 10; 10/35 = 0.

    285, 0.285 multiplied by 100 = 28.57%. That is, it turns out that our wood has a moisture content of 28.6%.

Some more tricks

Elimination of cracks and chips on wood. You can get rid of them not only by covering with putty. For this, you can use epoxy resin, which has a very hard structure, thanks to which this task is very easy to solve.

Note: This resin can also glue damaged workpieces.

5 carpentry tricks.</p><p> Little-known joinery life hacks. Life hack when polishing, do-it-yourself putty Nails should not be driven often along one line, this should be done in a checkerboard pattern. If you do this in slats of small thickness, then most likely it will crack.

And if you clamp it first with pliers, then this will not happen.

A knife for cutting sandpaper. If you cut it with scissors or a clerical knife, the blade becomes dull very quickly. We present to your attention a lifeform for cutting from a hacksaw blade attached to the end of the tabletop. We put washers under the blade on both sides.

Now fold the paper so that the fold is along the line of the desired cut. Then, effortlessly draw between the blade and the post. The paper is cut.

To correct the shortcomings after a beginner, remove the remaining gap between the bevels of the corners, press the screwdriver shaft against two surfaces of the parts beveled at an angle of forty-five degrees, and go along the edge. After that, no one will understand that there was no perfect joint.

( 12 marks, average 3.83 of 5 )

.

what for what + Video and Table
what for what + Video and Table

Posted By: Work Style |12, Nov 2020

Choosing between tiles and laminate
Choosing between tiles and laminate

Posted By: Work Style |08, Nov 2020