Carpentry tricks and life hacks

Carpentry tricks and life hacks Little-known and useful carpentry life hacks + photos and videos

Today we offer you to talk about what life hacks exist for a carpentry workshop. These tricks will simplify and speed up the creation of any wood product.

Life hack for grinding with sandpaper. Most often, we do not use a special emery block, but ordinary emery paper. This will make it possible to smooth out sharp edges, and also penetrate into narrow cracks and other hard-to-reach places.

But keep in mind that the higher the grain level, the thinner the paper will be, which will act as a base.

The result is that the higher grit sandpaper breaks even before the grit begins to wear off. To avoid this, you should glue the back of the sandpaper with standard or reinforced tape. This sandpaper will last longer and be flexible enough to smooth edges with a small radius.

Life hacks for carpenters

How to get rid of dents on wood

Dents on wood are a rather unpleasant thing.

But don't worry - there is a way to get rid of them! Moisten a cloth with water and shake it slightly to remove excess water. Place a damp cloth over the dent. Water will start to get into the wood fibers, and rightly so. So, using an iron, which is set to the maximum temperature, you should iron a cloth, and run the iron back and forth and in a circular motion.

Press the iron firmly to the surface and continue ironing until the cloth is dry (note that this does not take long).

The fibers of the tree will absorb water and straighten out, take their original shape. This procedure should be repeated over and over, adding more water until the dents are straightened out.

Joiner's life hacks for polishing

Carpentry tricks and life hacks You can perfectly polish surface with sandpaper and polishing paste, but this will take longer. In addition, a certain amount of dust constantly adheres to the surface before the coating has time to dry. What can we say about those coatings that dry out long enough!

In this case, the ideal option for you would be to use postage or even craft paper, which is folded several times.

However, it will have strong abrasive properties to soften the dust that has adhered to the coating without being coarse enough to damage it (assuming everything is dry). If the dust is not very much and the particles are not very large, then this craft paper hack will help you make the surface of your own product smooth, and the result will definitely impress you!

Sandpaper cutter

Cutting the sandpaper is the safest way to blunt a blade on scissors or even a clerical knife.Instead, we suggest you try our life hack with a hacksaw blade, which will be fixed to the end of the desktop.

Place washers under the blade on each side. This will allow the sandpaper to slide easily and effortlessly between the blade and the table.

A piece of sandpaper should be folded so that the fold follows the line of the desired cut - as shown in the photo.

Correction of the connection at 45 degrees

Carpenter's tricks allow you to correct many shortcomings that beginners often make during work. It's great when two pieces that are beveled at a 45 degree angle fit together perfectly to create an outer angle that is 90 degrees even!

Unfortunately, this is not always the case. We offer you a little life hack that will come in handy if there is a small gap between two beveled parts. It is necessary to press the screwdriver shaft to the joint at an angle to two surfaces at the same time, and thus walk along the entire length of the rib.

After that, no one except you will even know that the joint was not so perfect!

We make a clamp from a bottle for sealants

You may not have known that a sealant can is often used as a clamp? It is ideal for gluing small items such as cutting boards. To do this, you will need to place several pieces of wood or even cardboard on both sides and pull the trigger to create pressure.

Flexible emery block - DIY

Carpentry tricks and life hacks Sand curved surfaces in fact, it is not as simple as it might seem at first glance. Sometimes this may require an emery block that is flexible and durable at the same time. For this, none other than an ordinary thick notebook is perfect for you.

Wrap sandpaper around it, and then bend the notebook and give it an arched shape with the radius you require. Next, bend the edge of the sandpaper and insert it between the pages so that it does not start to slip. Be sure to try this life hack the next time you work with a curved surface.

Making hot glue without a gun

Yes, remember once and for all that you need to be ready for anything, and even for the fact that for an instant fix at any time hot glue is required. But not always there is an outlet at hand, into which you can connect a universal glue gun.

For this reason, you should always keep glue gun rods and the simplest lighter in your toolbox (in a pinch, you can get by with a box of matches) in case you need to improvise. Usually, in most cases, just a drop of a stick of glue is sufficient. Melt some glue with a lighter and drop it on the spot you want.

Life hack when sanding a smooth surface

Using a grinder and sandpaper, you can get a perfectly smooth surface of your wooden product. Before sanding the edge to surface joint, draw a zigzag line along the joint with a pencil.

If the edge protrudes above the surface of the board, which joins with it, then the drawn line will help determine this.

This way you will know for sure to continue sanding and will not rub off the plywood facing. Moreover, you will be able to determine whether the edge protrudes above the surface even with your own nail. To do this, you should run your fingernail without strong pressure along the joint perpendicularly. If the surface is flat, then the nail will definitely not "get stuck" in the joint.

And some more tricks

Putty for wood

Another carpentry life hack. If you have run out of wood putty, but you urgently need it, then you can do it yourself. To do this, we mix PVA glue, small chips (or dust after grinding) from wood and very little water. If you add a little chalk to the mixture, the putty will turn out to be much more plastic and will not start to "crumple". By the way, such a putty not only helps to perfectly close the cracks, but even pulls together the wood well.

How to hide chips and cracks

You can hide a chip or crack in wood from the eyes with a putty, or with epoxy resin. The latter version of the material is very solid and successfully copes with such a role. With the same resin you can "repair" the workpiece if you accidentally spoil it.

We drive nails correctly

that the board will crack. For this reason, nails should be driven in a checkerboard pattern.

Determination of wood moisture

If you need to determine the degree of wood moisture, but you do not have a special device for this, then you should saw off small control piece from wood and weigh. Write down the weight of the piece, and then dry it thoroughly in the oven at 100 degrees.

From time to time (once an hour) remove the test material from the oven and weigh. Wood can be considered dry when its weight ceases to change, because all moisture has come out of it. And then simple mathematics works.

According to measurements, the material weighed 50 grams before drying, and after 45 grams.

  • 50-45=5;
  • 5/45=0.111111111;
  • 0.11111111 * 100% = 11.1%.

It turns out that the moisture content of your wood (not dried) is 11.1%.

( 11 marks, average 3.45 of 5 )

.

DIY patina + video
DIY patina + video

Posted By: Work Style |05, Nov 2020

Stretch ceilings 3D with a picture
Stretch ceilings 3D with a picture

Posted By: Work Style |09, Nov 2020

which one is better to choose? Review + Photos and Videos
which one is better to choose? Review + Photos and Videos

Posted By: Work Style |05, Nov 2020