Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video When arranging a finishing floor covering, one of the main requirements for its successful installation is a thorough preparation and leveling of the base. The easiest way to solve this problem is using the technology of self-leveling self-leveling floors, from this article you will find out how much a self-leveling floor dries under tiles, laminate, linoleum or under a parquet board.

Types of self-leveling floors

When carrying out repair work, the question of planning the stages of construction is always tough, therefore one of the fundamental issues is taking into account the drying time of the leveling self-leveling floor.

Today manufacturers offer a varied selection of self-leveling floors, depending on the type of dry mix, on the basis of which it is produced.

The following types are distinguished:

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video Quick-drying mixtures - with a hardening period of up to 5 hours.

This type of quick-hardening self-leveling floor is optimal for further creation on its basis of designer floor coverings with a 3-D effect.

Based on cement mixtures - with a hardening period of 7 to 14 days.

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video Often used as a base for laying ceramic tiles.

Polymer mixtures - with a solidification period from 2 to 6 days.

Used for filling floors on an industrial scale with the possibility of adding pigments and additives, as well as an additional protective layer.

Installation on its basis of a laminate coating is possible.

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video Polyurethane mixtures - dry completely in 3 days.

This type of base is recommended for further laying of linoleum, and is also used as a base for installing laminate flooring.

Gypsum mixtures - period of complete drying up to 10 days.

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video This coating is not recommended for rooms with high humidity (bathrooms, corridors, kitchens, etc.

), but it is optimal as a basis for further laminate installation.

Epoxy mixtures - drying time from 2 to 5 days.

Very hardwearing.

Factors affecting the solidification of the self-leveling floor

Many of the above-mentioned self-leveling floors have a fairly wide range of complete drying times. This is due to the fact that there are a number of factors that affect the period of complete curing of the coating.

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video The thickness of the layer of the self-leveling floor

Often there is a need to align under a new coating an old base that has large differences in height, respectively, the layer of mortar in such cases will vary greatly in thickness.

In this case, drying will also be uneven.

The calculation of the drying time should be increased by 1.5 - 2 times relative to the standard drying time of the mixture.

Plane evenness

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video Although mixtures are often referred to as " self-leveling ", but when laying them, special attention should be paid to the process of leveling the screed.

Since self-leveling floors are quite thick in consistency, this process should be accelerated by leveling with a spatula, and to remove air bubbles from the mixture, use a needle roller.

Temperature

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video To optimize the drying process, it is important to observe the following characteristics - temperature indoor air should be in the range from +20 to +24 degrees Celsius. Sharp temperature changes are prohibited. Humidity should be between 50 and 60%. It is important to ensure that there are no drafts in a room with self-leveling floors while it dries.

The self-leveling floor should not be exposed to direct ultraviolet rays. It is recommended to cover the surface with a special film one hour after pouring the solution.

In situations where the self-leveling floor is mounted on a system of underfloor heating, it is prohibited to turn on the heating until it dries completely.

Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video When a self-leveling floor serves as the basis for a floor with a 3-D effect, the time of complete drying should be increased by drying of paints and protective coatings.

When preparing the surface of the base for pouring a self-leveling floor, experts advise to treat it with a quick-drying primer.

And 6 hours after pouring, cover with a protective varnish.

Choosing a self-leveling floor

Many companies producing mixtures for self-leveling floors release their products focused on the type of final floor covering that will be mounted on a self-leveling floor screed.

There are also options for mixtures for different layer thicknesses of the self-leveling floor from 2 to 80 mm.

In these mixtures, the manufacturer specially forms the composition of the components to optimize the drying time.

We recommend that you pay attention to the mixture of such manufacturers as:

  • Drying time for self-leveling floor? How much dries and hardening factors of the layer + Video Prospectors;
  • Knauf;
  • Foundations;
  • Hercules.

We hope that with the help of the information provided in this article, you will be able to calculate the time required to replace or install flooring in your home or office.

.