Getting rid of the creak of a parquet board: Solution methods with and without removal - Tips + Video

Getting rid of the creak of a parquet board: Solution methods with and without removal - Tips + Video Under the influence of various factors, the parquet is subject to drying out, soaking and deforming due to constant loads. These factors lead to the fact that the boards, when exposed to them, begin to squeak, thereby causing some discomfort. To determine why a parquet board creaks, you need to analyze the causes of this problem.

For this, it is important to study some especially this material

General information

Parquet construction

The material consists of three layers. The first, top layer is made of valuable wood.

The second, middle layer is formed from less valuable rocks and serves as an interlayer. The last, lower layer is also made from not expensive wood species. During operation, under the influence of a number of factors, deformation occurs, as a result of which delamination of the material occurs. Often, this causes the squeakiness of the parquet board.

Caring for and using parquet

Getting rid of the creak of a parquet board: Solution methods with and without removal - Tips + Video served for a long time, in the summer it is necessary to control the humidity in the room, and in the winter the optimal temperature regime must be maintained.

Do not forget that the flooring is susceptible to deformation under the influence of liquids, so when cleaning the premises there is no need to use a lot of water.

Parquet laying process

The parquet board is mounted to the floor by gluing and using a substrate. Remember that minor installation errors can lead to squeaks during further use. Any gap between parquet boards at the moment of friction between them will lead to a squeak.

Parquet processing

During the production process, each parquet board is treated with a protective layer of varnish, or with an oil composition.

Due to poor-quality processing with these compounds, the condition of the board deteriorates in a short period of use.

The service life of the parquet

Due to the fact that the thickness of the upper layer of the parquet is small, it wears out and is damaged during operation. It can also cause a squeak.

Reasons for the creak of the parquet board:

  • unevenness of the floor (base) where the parquet board is mounted;
  • poor quality substrate;
  • the use of improper quality glue;
  • incorrect laying of the logs (if the base is wooden);
  • bad locking system of the parquet.

Note.

Remember that before laying the parquet, check the evenness of the base with a building level. Irregularities should not exceed 2 mm for every two meters of the base.

When installing a parquet board, it is necessary to observe the gaps between the covered area and the wall. It should be about 10 mm. In the future, it is necessary to adhere to the parallel laying of the boards so that there are no shifts in the locking systems.

Such shifts provoke a creak.

Ways to eliminate squeak

  • Uneven base. Use a self-leveling compound to correct the problem.
  • Getting rid of the creak of a parquet board: Solution methods with and without removal - Tips + Video Poor backing. To restore the repair of the parquet board, the entire substrate is replaced, or holes with a diameter of 10 mm are drilled in some areas and a solution of a cement-sand mixture is poured in a ratio of 1: 3.

    In the second case, the substrate will receive additional points of contact with the base.

  • Poor glue (peeling of the parquet from the base). The cardinal method is to open the entire surface of the exfoliation. Less time consuming, effortless and financially the next way. Places of exfoliation are preliminarily identified.

    In the center of these places, several marks are made at a distance of 15 - 20 cm from each other and pieces of masking tape are glued. With a drill with a diameter of 2 mm, drill through the board with scotch tape. Glue is collected in a clean syringe and squeezed into the void area. Drying time of the glue is about 60 minutes. After an hour, remove the pasted pieces of masking tape.

    Any heavy object can be used to adhere the parquet board to the substrate more tightly. At the end of the entire process, it is necessary to grout the drilled areas of wax, and then polish with a rag.

  • Squeak in castle zones. To eliminate the problem, the boards are wedged and the geometry of the installation is leveled, observing the parallelism of the lines.

Provided that the parquet board is laid on a cement screed

If, without observing additional layers of plywood, fiberboard, this in any case threatens peeling off the material from the floor.

As a result of the formation of voids, the unsecured board begins to creak. Experts advise to completely disassemble the floor, especially if you are not sure about the quality of the floor screed. If significant problems with concrete are found, the screed will have to be redone. An excellent solution to the mill is to buy a self-leveling mixture that is ideal for laying parquet. When pouring, follow the manufacturer's recommendations, observe the layer thickness.

The permissible fluctuations in the evenness of the floor should not exceed 2 mm.

If, after opening the parquet, you find several damaged areas, with a relative evenness of the surface in general, you can do with local repair of the parquet board.

  • Clean the base of the insulation;
  • Remove dust and dirt;
  • Rinse with clean water;
  • Pour in concrete and level;
  • After the screed has grasped, cover the floor with a wet cloth;
  • Keep the area damp for 7-10 days.
  • Leave to dry for 3 weeks.

If a loose fit of a plywood board under a parquet board is found, which, in particular, becomes the reason for the squeak of the parquet, it is impossible to do without a significant repair with a complete replacement of the material.

If things are not so serious, and squeaks are heard in some places, try to dismantle the parquet boards locally. Drill holes in the plywood and pour in the cement mortar. Repeat the procedure after 24 hours. This will help provide additional support.

Errors in laying floors from a parquet board

Poor system of locks.

By observing the rules for laying parquet, you will save yourself the need to periodically repair the floor covering. The laying of the material is accompanied by the shift of the boards when the locks are snapped in at the edges of the boards. As a result, the rows hit the wall, and a creak occurs. In order to avoid this, wedging of each laid row is done. This approach gives a guaranteed result, and you will not wonder why the parquet board creaks after installation.

When buying parquet, pay attention to the quality of the joints and the flatness of the board.

There is no space between the elements. If the laying is too close to the walls, the parquet begins to creak. As the humidity level in the room rises, the wooden board expands and makes a creaking sound when pressed. Maintaining an optimal 100mm clearance will avoid further trouble.

Parquet peeling from the floor. If you find a problem, use a simple method to partially repair a parquet board.

Tips for using parquet boards

Even if the rules and regulations for laying parquet are observed, situations arise that require partial or major repairs of the coating. Natural material wears out over time, it is not always possible to maintain the optimal level of moisture in the house and parquet maintenance. The tree constantly absorbs and gives off moisture, expanding and contracting at the same time.

Very often, the reason for the creaking lies in this feature of the material.

At the start of the heating season, a characteristic squeak can be heard.

  • Compliance with the humidity regime in the house will avoid problems. Optimal indicators are at the level of 50-60%. It is important to adhere to the rules of parquet maintenance.

    Do not wash the floors with a too wet cloth. Water will seep through the holes and locks, after which the material will swell and lose the ability to linearly move.

  • The opposite side of excessive humidity is excessive dryness of the room. In this case, the board dries up and cracks, a creak appears. To eliminate the problem, dismantle the sounding boards, fill the space with cardboard, and put the parquet elements back.

    Use nails to fix it.

  • Select backing . The service life of the flooring depends on the quality of the substrate under the parquet board. The material of proper quality smooths out the differences in the floor, provides additional sound and waterproofing. The polyethylene foam backing provides for the use of additional waterproofing materials.

    This is due to the fact that the parquet cork board will start to rot from moisture penetration. An excellent choice would be a two-layer film backing, with an intermediate layer of expanded polystyrene. The underlay prevents popping and squeaks.

.