How to close pipes with a plasterboard box: expert recommendations

How to close pipes with a drywall box: recommendations of specialists

Special situations often arise during cosmetic repairs. For example, the question arises of how to close pipes with drywall with your own hands. Heating pipes, sewer pipes in the corner of the bathroom, water pipes in the kitchen spoil the aesthetics with their appearance and, in general, do not have the best influence on it. It is for this reason that it makes sense to hide them. The easiest way to do this is with drywall, since processing with this material will not cause problems even for those who have no experience.

Knowing how to close pipes, you can proceed in the same way for any kind of pipes (for example, for gas pipes).

We invite you to learn the most elementary way to solve problems with pipes - to make a box for pipes from GK with your own hands.

Tools and fixtures

To start the work process, first you need to prepare materials and fixtures according to the list.

To make a box you will need:

• Two panels of moisture resistant drywall (trim, which remained after wall cladding, dimensions not less than 0.5 * 0.

  5 meters are also suitable).

• Metal profile - the quantity is determined by the length of the box (from 5 to 25 meters).
• Self-tapping screws for metal.
• Set of dowels 0.6 cm.

• Mesh for making plasterboard reinforcement.
• Putty.

Before starting to sew pipes with drywall sheets, you should prepare the following tools:

• Building level to control the evenness of surfaces.
• Tape measure - you will need it to take measurements, and also with its help, you can cut drywall panels and metal profiles.
• Pencil, used to mark the material, to cut it or to install fasteners.

• Rotary hammer / drill with drill bit and 6 mm bits to make holes in the wall for dowels.
• Hammer.
• Phillips screwdriver.
• Hacksaw.
• Scissors for metal.

• Serrated trowel for smoothing grout.
• Spatula for spreading the putty on the surface of the plasterboard.

Who does not know how to make a box for closing pipes from drywall, below can get acquainted with the step-by-step process. But first, you should clearly define and understand why plasterboard panels are considered the ideal material in order to mask pipes in a bathroom, toilet or any other room. This choice is due to a number of advantages when working with this material.

These include:

• Affordability.
• Speed ​​and ease of assembly.
• Neutrality of the material for human health, its safety at the ecological level.
• Lack of release of toxic substances when heating sheets.

When you know all the subtleties, you just have to make the right choice in favor of a variety of material.

For rooms with high humidity, it is recommended to use moisture-resistant drywall, which differs from other types in green.

Carrying out work

Preparatory work

Before you start lining the pipes of the riser in the bathroom, you should prepare the room properly , in particular pipes. To begin with, you should clean off the old coating and apply fresh paint. This is required so that the life of the pipes is extended by protecting the paint from the corrosion process. The fact is that after closing the pipes by means of the box, access to them will be difficult, even if a hatch is made on the front wall of the box.

When the paint on the pipes dries up, this will mean that the time has come for the next stage - the creation of a frame structure for the box.

Erection of a support from the frame

As a rule, in the manufacture of the frame, metal profiles are used, which are made of galvanized sheet with a long shelf life and resistance to rust. Sometimes the frame for the box is made of wooden beams. In order for the risers to be hidden behind drywall, the profile support is erected with an orientation to the sequence of procedures.

1. Marks are made on the walls, ceiling and floor for the future frame, while you will need a pencil, a building level and a plumb line.

2. Further along the markup, you can begin to set the guides, and fix them to the wall surface using dowels.
3. The completion of the construction of the frame consists in the installation of rack elements along the guide profile beams. The connection of the profiles, which are joined to each other, is performed using special fasteners, which in the common people are called bedbugs.

So, let's move on to the most important thing.

Sheathing of the frame with sheets of GK

The next step is to sew up the fabricated base, a workpiece made of gypsum fiber.

Here you should pay close attention to the following nuances:

1. Use only moisture-resistant drywall panels.
2. Panels should be selected with a thickness that can give the box more rigidity (i.e. 1.2 cm).

3. When joining drywall workpieces, either edge alignments (if there is a factory-type edge) should be used, or by laying a chamfer at an angle of 45 degrees.
4. A gap is made in the skin so that everything is naturally ventilated.
5. Check the position of the caps of the self-tapping screws - they should be sealed, and not exposed and not dangling over the wall.

So, first, take measurements. After that, calculate the size of the gap between the floor and ceiling using a tape measure.

Measure the required distance on the profiles and cut in such a way that you get 3 blanks at once.Three posts should be placed around the pipes (2 of them should be against the wall and 1 in the center between the first two), while maintaining a right angle between them. If the risers are not located in the corners, but along the wall, you will need to prepare 4 pieces from a metal profile. They will need to frame the pipes in the shape of a square, or use three posts, bevel the corner and create a triangular support. When choosing frame geometry in order to sew up pipes with drywall, be guided by considerations in order to best suit the design.

After the gaps between the racks are measured, you should make support-crossbars, which are fixed with self-tapping screws for metal. It should be noted that in order to prevent deformation of the frame installation during seismic shifts, a special shock absorbing tape should be used. It should be applied to the contact areas of the working surface on the racks. The use of such a tape also makes it possible to neutralize vibrations, and this will prevent them from reaching the profile. Due to this, you will have protection against destruction of the frame structure.

Sheathing with drywall sheets is performed according to one of two scenarios - either with pieces of material that was prepared according to measurements, or with a single piece of material with the removal of extra centimeters after fixing it with self-tapping screws. If there is a shortage of a certain part of the sheets, the joints can be laid in place of the crossbars, and after the edge of the two parts of the sheets, they should be fixed. The resulting voids between the wall and the cladding should be filled with polyurethane foam.

Finishing the plasterboard box for pipes with putty is considered the final work. But before that, the joints of drywall with each other should be glued with serpyanka tape.

In order to give the ideal evenness for the surface, the caps of the fastener parts should be well putty.

To get even corners, use sloped corners. On its back, a little putty mixture should be applied, and when pressing, apply it to the corner. After that, using a wide spatula, it will turn out to achieve the effect of a leveled wall. When the putty is dry, the surface can be passed over with sandpaper and primed.

After that, you can start finishing work - gluing wallpaper, painting or laying tiles.

Sheathing pipes by other methods

Anyone who thinks that sheathing pipes with a plasterboard box is difficult or even impossible for some reason will and continue to look for solutions to the problem - how to close the pipes in the toilet with drywall. The creation of a protective wall is one alternative. When creating such a wall, a door or a revision suite with swing doors must be provided in it. The surface of the wall should be covered with materials that were used for the design of the bathroom.

Often, a frame for a hanging toilet is masked behind such a wall, and the installation of the structure should be carried out according to the technical instructions that are attached to the product.

Now a little about design. Hatches and doors can be completely separate, and they can be finished with tiles. For their better opening, you should use special hinges for fasteners, which are also called frogs. You can also make jalousie doors or install roller shutters.

As you can see, drywall finds beneficial use in such matters as the installation of all kinds of structures that hide utility lines from prying eyes. It is only important not to forget that in this case you should buy a special type of material (moisture resistant) and be sure to follow the instructions.

( 1 grade, average 5 of 5 )