How to drive a nail into any surface correctly

How to drive a nail into any surface correctly How to hammer a nail correctly : the best life hacks from the masters

How to drive a nail correctly? It seems that any self-respecting man should know the answer to this question. But if everything is really as simple as it seems, then why every now and then you have to hear about a cracked board, a layer of plaster that has fallen off, bent nails and broken fingers? What are the rules, secrets, nuances for carrying out this manipulation? Let's see.

Each nail has its own hammer

The simplest joinery hammers come in four typical sizes:

  1. How to drive a nail into any surface correctly MCT-1 (handle length from 25 to 28 cm, working part 9 cm, and the whole 0.25 kg) and it needs to be hammer in parcel nails, as well as wallpaper nails (up to 4 cm long).
  2. MCT-2 (handle length from 30 to 32 cm, working part 11 cm, and the whole 0.

    5 kg). It is needed in order to hammer in larger metal products. This tool is universal, the most versatile.

  3. MCT-3 (handle length from 30 to 32 cm, working part 12 cm, and the whole 0.8 kg).

    Such a hammer will cope with the same tasks as the MCT-2, it just has a little more weight.

  4. MCT-4 (handle length from 35 to 37 cm, working part 13 cm and more, and the whole 1 kg). It is needed in order to hammer in large nails, the length of which is more than 8 cm, as well as for dowel nails.

Naturally, the wallpaper nail is able to get into place quite well with the help of the fourth hammer model, but with the normal size of the percussion tool for the set purpose, it will be much easier, more convenient and faster to work.

Basic life hacks for hammering nails

Consider a few life hacks:

  1. It is worth starting hammering with light movements, and you can start sharp blows only after you make sure that the nail has started to enter correctly.

    It is worth holding the hammer by the end of the handle, making blows, and also try to concentrate and carefully look at the head of the product. Remember that the fewer blows you make to the product, the more reliable and quality everything will hold. Three or four wrist and two or three elbow solid blows will suffice.

  2. If you are working with a material such as wood, it is worth making sure that the diameter of the nail is not more than a quarter of the thickness of the board. For thin boards, it will not be superfluous to blunt the product - it is worth removing everything sharp with the help of a tool such as nippers.

    The fibers will then close and break, but the wood will not split later.

  3. For the strength of the connection of two boards, nails should be chosen so that they can completely "penetrate" the first and not less than a third enter the second. If you drive in the fasteners at an angle to each other, then the overall strength of the structure will become even greater.
  4. If necessary, it is worth lubricating the tip of the nail with wax, or even soap, so that all the work would go like clockwork.
  5. It is not recommended to hit many nails in a single line at a short distance from each other, as in this case the board will split.

  6. Heavy hammers can be used as support for floating joints.
  7. So that long nails that are driven into hardwood do not bend, if it is necessary to hold them as close to the head with pliers.
  8. If you want to install the mount as close as possible to the edge of the board, then it is imperative to seal this place with a hammer and punch.
  9. How to drive a nail into any surface correctly By the way, it is the punch that can help to deepen well and, in general, correctly drive a nail into the wall for plastering - it will be enough to attach it to the head of the product and hit it slightly with a hammer. If for these purposes it is possible to use only a hammer, then it will not be possible to avoid dents in the area.

  10. Before starting to drive a nail into the wall surface, which is covered with wallpaper, make a cross-cut in the covering with a sharp blade. Next, you need to carefully spread the corners to the sides, install the product for fasteners and glue the corners.
  11. The wiring from the phone, before nailing it, should first be pierced with nails - in the middle, very carefully, so that they do not touch the veins at all.
  12. Most DIYers often wonder which hand to hammer in nails with. It simply won't work to drive a product into concrete or wood for fastening by hand - this is an obvious fact for any sane person.

    But sand, clay, or into the ground - very much, the main thing is that you are extremely careful and do everything confidently.

  13. So that beginners can "save" their fingers from being hit by a hammer, you can use the simplest clothespin.

Most often, the question of exactly how to drive in nails arises when you work with hard-to-reach areas of the surface. For example, if we are talking about installing fasteners in a recess, but you just need to purchase a steel core and a metal tube, and you can assume that you already have no problems. Look at the pictures and see for yourself!

You can install the product for fastening in an inconvenient nook with a bolt and a nut:

  • Tighten the nut slightly on the bolt.

  • Place such a "device" on the head of the nail.
  • Hit the nail with blows to the head of the bolt.

When making various beautiful crafts or repairing wooden pieces of furniture, you often have to turn to dowels - large nails made of wood. As the steel ones are usually forgotten, you cannot beat them. First you need to drill a hole, drop a little glue into it, and only after that you can drive in the dowel.

How to properly hammer the dowel nails

If we are talking about concrete, then do this:

  1. Mark the hole with a center punch and hammer.
  2. Use a hammer drill to punch a hole to the desired depth. Here you should immediately pay attention to the fact that on the surface of the drill there is a marking indicating the diameter - it must necessarily coincide with the marking of the dowel. The depth of the hole must necessarily be greater than the length of the dowel by about 0.5 cm.

Note, in the event that you do not have the opportunity to use or even find a puncher from someone.

  1. Use a vacuum cleaner to remove the remaining dust.
  2. Use a hammer of the correct size to deepen the dowel holder.
  3. Drive in the nail that came with the dowel to the depth you need, and leave a few millimeters from the head for suspension.

To drive a dowel into a brick, you need:

  1. To properly drive a nail into a brick wall, first you need to determine the best location for the dowel, and while taking into account the fact that this should be the center of the brick.

    The fact is that the solution for the cargo is completely unreliable, and therefore it is definitely not worth the risk.

  2. Bricks should be drilled with a hammer drill. You need to start slowly and carefully so that the masonry does not split, and after overcoming the 1 cm barrier, the rotational speed of the drill may return to normal.
  3. Remove all brick dust and chips from the hole.
  4. Drive in the cartridge and nail.

To drive dowels into ceramic tiles or tiles, you need:

  1. First, select the location of the dowel entry and use a marker. This can be both the tile surface and the seam.
  2. Mark the surface with a metal self-tapping screw. Perform very simple and light tapping, and no more than 0.05 cm of enamel should be passed.

  3. Using an impact drill with a metal drill (the diameter should be 0.3 cm), drill the entire thickness of the tile.
  4. Bring the hole to the size you want.
  5. Drill the wall under the tiles according to the instructions for brick or concrete.
  6. Carefully install the dowel and nail.

For drywall:

  1. Before driving in, you should think carefully about whether you will ruin these actions surface. If you plan on placing a heavy load, then this material will not be the best choice for support.
  2. For lightweight items, the moth mount is designed specifically for low load bearing bases.
  3. Make a hole of the desired diameter in the drywall surface.
  4. By tapping, insert the mount all the way into the hole.

  5. Tighten the screw by hand or with a screwdriver.

That's probably all. Now you know exactly how to drive in nails and dowels correctly.And never forget to protect your fingers!

.

Tips for placing flower beds + Video
Tips for placing flower beds + Video

Posted By: Work Style |06, Nov 2020

types and characteristics + Photo and Video
types and characteristics + Photo and Video

Posted By: Work Style |09, Nov 2020

Which is better? Cast, extrusion- Popular brands
Which is better? Cast, extrusion- Popular brands

Posted By: Work Style |03, Nov 2020

Selection of anatomical orthopedic mattresses
Selection of anatomical orthopedic mattresses

Posted By: Work Style |02, Nov 2020