Wood is an excellent finishing material, but, unfortunately, not durable. To extend its service life and preserve its appearance longer, a variety of protective agents are used, differing in composition and mode of action. One of these tools is Pinotex, which is widely used in both private and industrial construction.
Pinotex for outdoor woodwork
Trademark "Pinotex" unites a whole line of deep penetration wood protective compounds - antiseptics, impregnation, primers, oils, paints. But most often this name means an alkyd-based tinting antiseptic.
Wood protection products for wood Pinotex
The owner of the Pinotex brand is the Swedish-Finnish concern Akzo Nobel, and its products are already a lot has been holding leading positions in the European market for years. The advantages of the protective agents of this brand are obvious: low consumption, high quality coating, excellent decorative properties. In addition, for each stage of wood processing, there is a separate composition that necessarily contains fungicides.
Wood protection Pinotex
Pinotex for outdoor work on wood is conventionally divided into three types: primers, compositions for facades and compositions for doors and windows.
The primers contain the bulk of antiseptics, and in combination with the topcoat they are able to provide maximum protection against decay.
At the same time, the use of a primer before applying other Pinotex formulations is not a prerequisite, and many do without it. This is justified in cases where the external surfaces are protected from direct exposure to precipitation and the risk of mold growth is minimal.
The facade is treated with Pinotex primer
But the treatment with the primer itself, without the use of additional coatings, gives protection only up to 3 months when applied in the summer, and approximately 5 months in the cold season. The fact is that the film that the soil forms on the surface of the tree is not strong enough and is gradually washed off in rain and snow. Its resistance to ultraviolet light is also low, so the top layer of the material quickly fade in the sun.
|Treatment of sawn and planed wood against biocorrosion. It is used as part of the Pinotex decorative and protective coating system||Deep penetrating colorless composition with high adhesion. It is applied with a brush in 1-2 layers, dries up in 24 hours.Consumption for sawn wood is 160-175 g / m2, for planed wood - 100 g / m2|
Pinotex Wood Primer
| Treatment of wooden external surfaces from rot, mold, blue. Part of the Pinotex Doors system. |
|Colorless water-soluble composition, penetrates deep into the structure, has high adhesion. It is applied with a brush in 1-2 coats, dries for 24 hours, consumption is up to 180 g / m2 for sawn wood, 100 g / m2 for planed wood|
Primer Pinotex Wood Primer (Wood primer). Download
Pinotex Wood Primer full description
These agents, in addition to antiseptic properties, have increased resistance to atmospheric influences and ultraviolet light. They penetrate deeply into the structure of the tree, give the fibers a more intense color, and form an abrasion-resistant film on the surface. Subject to the technology, the surfaces treated with these compositions retain their magnificent appearance for 8-10 years.
Water based Pinotex Aqua Protect impregnation
|Compositions for facades||Purpose||Main characteristics|
|Weatherproof protective impregnation (stain), used together with Pinotex Base primer. Emphasizes the natural beauty of the material, gives color to the texture|| Semi-matte finish, contains active ingredients against blue stain and fungus. The color palette includes 9 woody shades. It is applied with a brush in 2-3 layers, interlayer drying 12 hours, complete drying - 24 hours. Consumption for sawn wood is 9 m2 / l, for planed wood - 16 m2 / l. |
The service life of the coating is about 6 years
Pinotex Aqua Protect
|decorative impregnation, provides the material with resistance to weathering and emphasizes the texture||Water-soluble composition containing wax and wood oil. The palette includes 120 color shades. It is applied in 2-3 layers, interlayer drying is 8 hours, full drying - 16 hours. Consumption for sawn material is 8 m2 / l, for planed material - 15 m2 / l. Service life - up to 7 years|
Pinotex Lacker Yacht
|Varnish on alkyd-urethane base, intended for the treatment of substrates exposed to intense moisture and mechanical stress|| Colorless composition with a glossy and semi-matt degree of gloss. |
Forms a very durable coating with water and dirt-repellent properties, does not drip, easily spreads over the material. It is applied with a brush or a special applicator in 2-3 layers. Interlaminar drying takes 4 hours, complete drying 48 hours. Consumption is about 15 m2 / l
|Decorative impregnation with protective functions.Used together with Pinotex Base, it gives the material a more intense woody shade, prevents fading|| Colorless composition with UV stabilizers and UV filters. |
It is applied with a brush in 2-3 layers, interlayer drying takes 12 hours, complete drying - a day. Consumption for sawn wood 8 m2 / l, for planed wood - 12 m2 / l
Pinotex Tinova Professional
|Protective agent with the highest possible resistance to negative effects. Recommended for use in combination with Pinotex Base|| Water-soluble compound that forms a very strong coating resistant to freezing, moisture, fading and fungal attack. The color palette includes over 60 woody shades. It is applied with a brush in 2-3 layers, interlayer drying 12 hours, full drying - 24 hours. |
The service life of the coating is up to 12 years. Consumption for sawn wood is 8 m2 / l, for planed wood - 12 m2 / l
|Impregnation with decorative and protective functions. Designed to treat wood against mold, algae, precipitation and ultraviolet radiation. It is applied systemically with Pinotex Base|| Semi-matte composition with a high content of active additives. The service life of the coating is up to 8 years. |
It is applied with a brush in 2-3 layers, interlayer drying - 12 hours, full - 24 hours. Consumption for sawn wood is 8 m2 / l, for planed wood - 12 m2 / l
Impregnation for wood Pinotex Ultra
Contains active additives against mold and algae
The impregnation includes white alcohol, alkyd resin, fungicides, pigments, UV filter and functional additives
This is how the impregnation itself looks when opening the can
Impregnations and varnishes of this group are specially designed for surfaces in contact with both the external and internal environment. Window and door frames are most susceptible to deformation from moisture and temperature extremes, rotting, and fungus often appears on them. Mechanical effect means a lot, from which ordinary paint is quickly erased or covered with microcracks. Pinotex antiseptic impregnations can eliminate such problems and preserve the original appearance of wooden structures for 6-8 years.
Pinotex Doors. Windows
| Water-soluble impregnation with active ingredients against mildew and blue stain. Used together with Pinotex Wood Primer, it provides protection from ultraviolet radiation and precipitation. After applying the impregnation, the painted surfaces do not stick together. The composition is applied with a brush in 2-3 layers, interlayer drying is 4 hours, complete drying - after 12 hours. |
Consumption for sawn wood - about 11 m2 / l, for planed wood - 13 m2 / l
Pinotex Lacker Aqua
| Water-soluble tinted varnish. Forms a smooth, flexible coating with water and dirt repellent properties. Emphasizes natural texture, spreads easily over the surface, does not leave streaks. The color palette includes 44 woody shades. The treated material is resistant to scratches and other minor damage, detergents and abrasion. |
The coating does not crack or turn yellow over time. According to the degree of gloss, it can be matte and glossy. It is applied with a brush in 2-3 layers, dries for 4 hours, the consumption is 13 m2 / l
All the compositions described above are used for open surfaces that are directly exposed to atmospheric influences. But there is a separate tool for hidden wooden structures such as logs, rafters, lathing for facade cladding. This impregnation is Pinotex Impra - a water-soluble composition with biocides.
It tends to quickly penetrate deep into the structure and be evenly distributed between the fibers. Structures processed by him are practically not affected by rot, mold, insects.
Wood protection impregnation for hidden structures
Pinotex Impra is not suitable for open surfaces, since UV radiation destroys biocides and completely deprives the impregnation its antiseptic properties. The composition spreads easily, does not drip, dries for about 2 hours. It is applied with a brush in 1-2 layers, the consumption is 10 m2 / l for sawn wood and 14 m2 / l for planed wood.
The Pinotex compositions are most effective when processing new wood. If the material has already been impregnated or painted with something, the antiseptic will not be able to penetrate deeply into the structure, and the protective properties will decrease. This is especially true of wood treated with linseed oil. In the same way, the decorative effect is reduced, because the texture of the fibers has already undergone changes, and it will not be possible to return the original natural beauty of the wood. But this does not mean at all that Pinotex cannot be used for such materials - it suits any wooden surfaces, the main thing is to prepare them correctly.
Photo - harmful fungus
Having found such places, you need to cut off the resin with a knife and carefully process the base with white spirit or turpentine.Further, the surface is recommended to be sanded with an abrasive nozzle to improve the appearance of the material and facilitate the absorption of the soil.
If the coating adheres tightly, another method is more suitable - treatment with a chemical wash. The product is applied to the surface in an even layer, left for a while and then scraped off without much effort. Finally, the tree should be rinsed with clean water and dried in the fresh air.
Old paint on wood
How to remove old paint
Thermal method of removing paint
Metal parts such as nail heads or staples that hold wood together should be sanded and primed on metal.
Alkyd anticorrosive primer
To seal wormholes and grooves, you need to choose a putty for wood of the appropriate shade. If the color does not match, it is clearly visible under the transparent impregnation, which negatively affects the decorative effect of the coating.
Putty on a wooden surface
After that, the material is rinsed with water and dried.
Wood bleach NEOMID 500
Wood bleach ECOSEPT 500
Blockhouse before processing
It is recommended to prime the surface with Pinotex in dry, windless weather at a temperature of 18-20 degrees and an air humidity of no more than 80% (the optimum value is 65%). At temperatures above + 25 ° C, moisture from the primer evaporates too quickly, and the composition does not have time to penetrate to the desired depth of the structure. The same happens when processing surfaces heated by the sun: getting on a hot tree, the soil begins to set in a matter of minutes and forms a thin, weak film on the wood. Such a coating is easily erased and cannot provide reliable protection against the penetration of microorganisms.
That is why for processing facades on the south side, you should choose a cloudy day or primed in the late afternoon, when the activity of the sun's rays decreases.
Primer Pinotex is a ready-to-use solution, and therefore does not need to be diluted. For application, a paint brush with a dense synthetic bristle of medium length is most often used.
Tools for work
Preparing the tool, open the jar with primer
Step 1. Thoroughly mix the primer in a container, dip the brush to half the length of the pile and apply to the surface along the wood fibers.
The layer should be continuous and as uniform as possible, the composition should be well rubbed over the wood.
Mix the primer
Step 2. Having processed straight surfaces, go to the end sections. Here, the soil should be applied more abundantly so that the sections are well saturated. Small individual elements are most conveniently processed by dipping in a solution.
Cover the logs with soil using a brush
Step 3. After applying the first coat, allow the surfaces to dry. A day later, the material is primed again in the same sequence.
Apply the second coat after 12 hours
The top coat can be applied after day
Shades of wood after applying the first and second layers
At least 24 hours should elapse between priming and finishing for the primer to dry completely. Environmental requirements remain the same: humidity 65%, air temperature 18-20 degrees, shading from direct sunlight and no wind.
Application of impregnation
The selected composition for the topcoat is mixed well and applied in a continuous layer along the fibers. The layer is made as thin as possible, rubbed well on the wood with a brush so that no sagging remains. For a pronounced effect, 2-3 layers are required, which are applied at regular intervals. The interlayer drying time must be indicated in the manufacturer's instructions, so carefully study the information on the packaging.
Wall after treatment
After applying impregnation, the wood retains its naturalness
At this point, the processing of the tree by Pinotex is considered complete.
If everything is done correctly, it will be necessary to renew the surface no earlier than in 5-6 years, or even all 10, depending on the type of coating. For reprocessing, it will be necessary to clean the base from dirt and dust, lightly sand with fine sandpaper and again coat with Pinotex impregnation in 2-3 layers.
Useful properties of Pinotex antiseptic allow you to use it for processing any types of wood
Posted By: Work Style |02, Nov 2020
Posted By: Work Style |09, Nov 2020
Posted By: Work Style |05, Nov 2020
Posted By: Work Style |10, Nov 2020
Posted By: Work Style |11, Nov 2020