Step by step instructions and Drawings + Photo and Video

Step by step instructions and Drawings + Photo and Video Do-it-yourself budget options for sliding gates: drawings, photos and videos. The selection of the design of the fence and the material of manufacture is always a certain compromise between possibilities and desires, and the choice of the entrance group (gates and wickets) is something that cannot be saved on. But if you need to get a design that will be inexpensive, we suggest doing it yourself.

For this reason, budget options for sliding gates with their own hands became the topic of the article. This will save a lot of money, and you can do what you like.

Option # 1 - sliding gates

An interesting option would be to create sliding gates, but not quite ordinary ones. This option has an upper suspension, which means that the finished structure will be relieved of the standard set of disadvantages that are inherent in conventional gates. Home experts say that when studying a huge amount of materials for the manufacture of industrial doors with a rollback, they most often suggest a design with a lower position of the roller trolley. But this is not the best option.

In this case, you will have to clean the gate from snow, mud and ice from under the roller carriage beam all the time in winter.

There is also a certain limitation on the lifting height in standard hanging doors with a top beam. A way out of the situation would be to create a gate without overlapping the sash.

First you need to pour the foundation. Although budget construction is supposed, it is necessary.

Initial data:

Now about the pillars:

  • The first pillar is a profile pipe with dimensions 8 * 4 * 0.

    2 cm.

  • The second post is load-bearing, has a cross-section of 8 * cm. It will need to be welded from two shaped pipes with dimensions of 8 * 4 cm.
  • The third post is also made of shaped pipes and has dimensions 8 * 4 * 0.2 cm .

  • The fourth pillar will be the last one, made of a round pipe with a diameter of 7.6 cm.

Although the foundation is initially poured under the trolley with rollers, the structure can be changed and made suspended ...

To do this, you will need a guide beam (base), on which the carriage rollers will "walk". As a base for the guide, you will need to purchase a rectangular pipe with a size of 6 600 * 8 * 4 * 0.45 cm. The weight of such a pipe will be about 50 kg. After that, using a grinder, cut a groove along the entire length of the profile in the narrow part, which will be 1 cm wide.

The finished beam should be fixed on four fence posts, while the slot should be located at the bottom. To do this, it is applied in place and marked for fasteners. Remember that how accurately this knot is made will depend on how easily the gate will pass. In order to make a sliding gate with your own hands, you will also need a welding machine.It is not that difficult to learn how to use it.

Since all work will be carried out alone, clamps and magnets will be required. An angle clamp will also be important, which will make it possible to connect the parts to be welded at an angle of 90 degrees. After welding the fasteners, the beam should be fixed to the supports and the manufacture of the leaf and gate carriages can be started.

For carriages, a spring attachment eyelet from Gazelka is ideal. The thickness of the metal will be 0.

8 cm and it has two holes with a diameter of 1.7 cm into which an M18 bolt can be inserted. Still required:

  • From the rear spring "step-ladder", but not from "Gazelka", but from ZIL-131.
  • 2 nuts marked M20.
  • Centering and main bearings.

To create a wicket and gate leaf you need:

  • 2 profile pipes (leaves), which have a size of 6 * 4 * 0. 25 cm and 4 * 2 * 0.25 cm.
  • 2 profile pipes (gate) with dimensions 4 * 2 * 0.2 cm and 2 * 2 * 0.

    15 cm.

It will be most convenient to assemble the structure on the assembly table or on an improvised slipway. This is many times more convenient than doing everything on the knee. In addition, the quality of work is improving. At the top, the attachment points of the carriages should be additionally reinforced with corners of 6.

2 * 6.3 cm and 5 * 5 cm. The sash assembly is performed with careful control of the corners and diagonals, since any inaccuracy or distortion can lead to the final rejection of the entire structure. If you work alone, then first expose the details, and after checking you can finally scald them.

Also, to reinforce the sashes, use additional welding of jibs, which will give the structure rigidity.

When adding them, imagine how the load on the structure will be distributed. Bearings should be pressed into the carriages on the axle, and after that the welded seams of the part should be cleaned and the assembly should be painted. After making the carriages, you should try them on in place to make sure that nothing gets hit and everything moves perfectly. Below and above, the carriage parts should be closed with rubber covers from the steering wheel of the Gazelle and VAZ gearbox 2101.

Step by step instructions and Drawings + Photo and Video Do-it-yourself budget sliding gates provide installation of a support bearing from GAZ024 between the fastening nut from the carriage stud to the lower plane of the horizontal upper frame of the sash.

Since the lateral clearances in the assembly are minimal, and the alignment of the bearings will occur due to roundings inside the corner on the pipe, the carriage will move perfectly.

After making the carriages, you can hang the gate, but until everything is ready, for convenience, you should substitute a supporting support under the sash. After aligning the gate wing and guide rail, the fasteners must be covered with a rubber boot.

When you are sure that everything is working well, a false frame can be welded to the sash. It can be made from a strip of 4 * 0.

4 cm. After that, the wicket and sashes are sheathed with profile galvanized sheet of the C8 brand and you can start making catchers.Use M10 bolts to limit travel, and be sure to wear rubber bushings on them. Also from metal plates with a thickness of 0.6 cm, make a roller guide for the gate.

4 rollers were used in the construction, as well as:

  • Corner 75, in which the "ear" was welded.
  • Wheels with a diameter of 30 mm, with a central hole (it will need to be reamed for an M8 bolt).
  • Bolts M10 - 2 pieces.
  • Grover (spring washer).
  • Washers and bushings.

  • M8 nuts / bolts - 4 pieces.

The system will work as follows: when the gate is completely closed, it will start to run over the lower safety catch, and when fully open, it will run over the bracket.

Option No. 2. Eternal gate

Consider another version of budget sliding gate with your own hands, which can be called eternal.

They have 6 attachment points. This is ideal if the road to the house is narrow, there are pillars near the entrance to the site and there is no way to put swing gates. Sliding gates are easy to make from pipes. As can be seen in the drawing, the system operates according to the principle "the simpler, the better", and this has been repeatedly confirmed by many years of practice. The design uses homemade rollers, machined on a machine.

The bearings should be inserted into the roller, and then I weld the assembly on the "pin", which is welded to the posts. The rollers are fixed with bolts. Such a system is reliable and simple, since in winter there is no need to clean snow and ice, because precipitation will not linger on the pipe. This gives a trouble-free and all-weather operation of the structure mechanism. According to the reviews of those who made such gates for themselves, even after several years they work like a clock.

The only negative is that rust appears in some places, but the structure itself did not sag.

Please note, that if you decide to repeat the design, choose pipes with a larger diameter than the roller width, otherwise the corrugated board screwed to the pipe will touch the roller.

The design is so affordable, successful and working that thousands of people use it. As experts shared their experience, to create the gate, they used a pipe with a diameter of 7.6 cm and a wall thickness of 0.

35 cm. In this case, the width of the entrance will be 4.6 meters and a wicket. Jumpers are a pipe with a diameter of 5.72 cm and a wall thickness of 0.

3 cm. They should be installed every 1.3-1. 4 meters. The rollers use double row bearings.

By the way, the weight of the door influences the choice of bearings. If you choose double-row parts, then they have a large margin of static and dynamic bearing capacity. These bearings can carry up to 210 kg per load point. As a rule, the gates are lighter, and therefore more than 6 times the safety factor is obtained. For supporting pillars, a square pipe 10 * 10 cm and with a wall thickness of 0.

4 cm is used. It should be concreted at a depth of 75 cm into concrete bumpers through a ditch.The bumper is 2.7 meters long, 1.2 meters high and 0.

3 meters wide. The support pillars should be connected vertically to each other, as well as diagonally by the jib. Weld a corner 4 * 4 * 0 from below. 4 cm.

Conclusion

As you can see, making a budget sliding gate with your own hands is not so difficult.

Both options presented in the article are reliable and time-tested. It all depends only on the characteristics of your site.

( 1 grade, average 5 of 5 )

.

Tips and Uses + Videos
Tips and Uses + Videos

Posted By: Work Style |09, Nov 2020

causes of mold development + Video how to get rid of
causes of mold development + Video how to get rid of

Posted By: Work Style |12, Nov 2020

Overview and Material Selection Tips + Video
Overview and Material Selection Tips + Video

Posted By: Work Style |04, Nov 2020

installation, how to paint, photo + video editing
installation, how to paint, photo + video editing

Posted By: Work Style |10, Nov 2020