In order to easily, reliably and quickly carry out the installation and installation of wooden lining, you need to know how and by means of which it is necessary to carry out certain repair work. It all depends on what kind of room you plan to sheathe.
Molded board is a building material, very convenient and reliable for installation. Each board has a special groove on one side and a protrusion on the other. And as a result of their attachment, a reliable lock is obtained.
After studying our article, you can easily do the installation of the lining with your own hands.
Tools and building materials that you will need for repair: wooden slats (20x40 mm); self-tapping screws and dowel-nails; building level; screwdriver; mineral wool; vapor barrier; mounting stapler; polypropylene twine; directly the lining itself; kleimers; a hammer; skirting boards; finishing nails and special bio-protective compound.
We start with the installation of the battens. To do this, you need wooden slats 20x40 mm, screws and dowel-nails, a building level and a screwdriver. The slats must be fixed on the wall, while placing them strictly perpendicular to the subsequent direction of the lining. Before fixing, check the evenness of the wall surface with a building level. If the wall is not completely level, place a piece of plywood under the batten and check for evenness again.
The spacing of the battens is no more than 50 cm The bottom rail is fixed at a distance of 5 cm from the floor. The top rail is installed at the level of fixing parts and elements of the ceiling. Also, the rails are fastened in all corners and around windows and doors.
An important point, all construction work on the installation of electrical wiring should be carried out before the installation of the lathing, since after the installation and installation of the lining it will be simply impossible.
After installation of the battens, we proceed to heat and waterproofing.
To do this, you will need a thermal insulation building material (mineral wool), a waterproofing building material (vapor barrier), an assembly stapler and polypropylene twine. You can install the vapor barrier before installing the lathing, and after that you put the second layer on top after filling it with mineral wool.
When installing and installing the vapor barrier, fasten it with the rough side to the insulation. Make a waterproofing or vapor barrier with an overlap of 10 cm and be sure to secure the joints with tape along the entire length. The waterproofing is fastened using a mounting stapler with a step of 15 cm.
So that the mineral wool does not slip and deform over time, it must be fastened with polypropylene twine. The polypropylene twine is also fastened using a mounting stapler.
Installation and installation of lining. For this work, you will need panels, finishing nails, a building level, a hammer and a small piece of lining. Before proceeding with the installation and installation, it is necessary that the unpacked lining lay for some time in the room in which it will be installed (at least 48 hours).
Always start the installation of the first wooden panel from the corner. Fasten to the crate with finishing nails or cleats. If you use cleats during installation, then in the future the lining can be easily dismantled on your own. After that, you can use this material during installation and installation in any other place.
After installing the first lining and its fastening , insert the tongue of the second panel into the groove and reattach.
The second and subsequent lining will be quite difficult to insert with your hands, most likely they will be difficult to enter. There is no need to buy a special tool to facilitate this process. You can do it yourself. To do this, take a small piece of a sawn-off wooden panel and, inserting it with a comb into the groove of the next lining to be installed, gently tap it with a hammer. This must be done along the entire length of the lining until it fits tightly enough.
Additionally, you can fasten the boards with nails from the top and bottom.
Measure every sixth board with a building level so that the installation is without deviations. There should be a gap of at least 2 cm between the clapboard and the bearing wall. This is necessary so that in the future the wooden wall remains perfectly flat without any major deviations.
After we have installed all the panels, we proceed to the installation of fittings.
At the penultimate stage, the following tools and parts will be needed: a hammer, baseboard, finishing nails and a dumbbell. We continue to build with our own hands. In order for the lining to take on a beautiful well-groomed look, it is necessary to attach all the corner joints and cover all the gaps between the ceiling and the floor. For corner joints, use a narrow skirting board; for the bottom and top gaps, use a skirting board dimensioned to cover these gaps. The fixing of the plinth is carried out using finishing nails.
And the final stage is wall processing. The final and very important repair procedure remained: the treatment of all mounted wooden walls with a fire-retardant special compound or impregnation. This must be done at least three times every next day. After this treatment, your walls will serve you for a very long time. It will be very warm in the winter and cool in the summer.
This completes the installation and installation of the lining! We hope that thanks to our article you will not have any difficulties with the installation and installation of the lining with your own hands! Good luck with your repair!
( 1 grade, average 4 of 5 )
Posted By: Work Style |01, Nov 2020
Posted By: Work Style |13, Nov 2020
Posted By: Work Style |13, Nov 2020
Posted By: Work Style |08, Nov 2020
Posted By: Work Style |04, Nov 2020