The seam between the bathroom and the tile - the better to seal, which is better? Silicone or Grout + Video and Photo

The seam between the bathroom and the tile - the better to seal, which is better? Silicone or Grout + Video and Photo The seam between the bathroom and the tile - what to fix. Until 20 years ago, there were few really good materials on the construction market that would help in the design of a bathroom. In the recent past, the favorite method was sealing the joints with cement mortar, and then painting with enamel paint.

But for the reliable and long-term use of this element of the bathroom, there was no hesitation of the subject.

But now, thanks to the intensive development of the chemical industry and the improvement of technologies, the market has been filled with a large assortment of this type of products, which make it possible to seal the seams between the bathroom and the tile gracefully and easily.

Design methods

When re-equipping a bathroom, the question often arises of what sequence to carry out the work in so that in the future there will be no water leaks at the joints tiles and bathroom. Experts in this field offer a large number of options for how to solve an actual problem, and can provide the best methods for solving your particular problem.

Planning the use of the bathtub for a long period allows the installation of the sides to the wall. When the plumbing is carefully fixed, you can start laying the tiles, and process the joint joints with inter-joint grout. But this solution has some nuances.

This completely eliminates the possibility of water leakage, which is a significant plus. But the disadvantages of the method of sealing the seams between the tile and the bathroom is the likelihood of breaking the masonry of the tile at the junction due to the poor stability of the bathroom.

In case of an unexpected replacement of this piece of plumbing, you will need additional financial investments and the time / effort required to dismantle the tiles and re-install them. In addition, the chance of finding finishing materials from the same collection is too small, and for this reason, replacing the bathtub can provoke a complete renovation of the restroom renovation.

It will be much more effective not to "embed" the bathroom into the wall, but to use special materials for sealing the seam between the tile and the bathroom.

The following options are very popular:

  • Use of material for grouting tiles.
  • Solution.
  • Use of polyurethane foam.
  • Treatment with silicone sealant.
  • Setting curbs.

  • Setting the curbs.

Each of these methods has its own advantages and disadvantages, which can be avoided if you use several methods at the same time. With a detailed review, you can choose the best option for your situation.

Instruction for grouting

Tile grout

The seam between the bathroom and the tile - the better to seal, which is better? Silicone or Grout + Video and Photo With a tight junction of the bathtub to the wall, you have the opportunity to close up the walls with a minimum of cost and effort. You can ensure a good fixation of the bath even with ordinary white grout, or with any other color with the shade you need.

The key advantages of the method are moisture resistance and color retention duration.

The level of protection against rust and external contamination can be significantly increased by using a fugue gloss treatment. But since the key condition in the form of a tight adhesion of the bath to the tile around the entire perimeter and stability is not always possible, you need to resort to more reliable options.

Using mortar

How else to close the seam between the bathtub and the tile, if not mortar? This traditional solution has a right to be. The method is economical, which made it popular.

In this case, it is permissible to use the remnants of tile glue or self-induced sand-cement mortar for registration. It will also be appropriate to seal the joint with plaster. An essential condition for obtaining a high-quality result is the thick consistency of the solution.

Sealing the joint involves the following steps:

  1. Thoroughly clean the surface of the bathtub and adjacent tiles from any dirt.
  2. Spray the area with water to improve adhesion.

  3. To prevent the mortar from falling under the bathtub, use a plastic mesh, which is used when plastering or filling the corner surfaces, and fix it at the junction of the bathtub and tiles. If you do not have a serpyanka available, you can replace it with other materials that will be fixed under the edge of the bath.
  4. When you apply a small amount of solution, it should be tamped well.

Important! Sealing the seam between the bathroom and the tile with cement mortar is impossible without additional protection against moisture ingress.

In order to increase the level of moisture resistance and make the interior aesthetically pleasing, the joint must be additionally processed.

For this, experts suggest using a water-repellent impregnation or epoxy resin. At the end, the bathroom is decorated with tiles or self-adhesive tape.

Polyurethane foam

The use of polyurethane foam will make it easier for you to seal the joint. When buying a spray can with the composition, you need to make sure that this foam has moisture resistant properties. Before you start, take care to protect your hands with gloves.

If there was no protective barrier, and the foam got on the skin, be sure to rinse this area well with water, and do not allow the material to dry on the skin.

The seam between the bathroom and the tile - the better to seal, which is better? Silicone or Grout + Video and Photo Just as when sealing the seam between the tile and the bathroom, first clean the surface from dirt. In this case, careful actions during the application of the material are the key to a high-quality result.

Try to avoid getting foam on unwanted areas. After complete drying, remove the residues by cutting with a utility knife.

In the end, you can use one of the popular finishing methods - tape, tile or curb.

Silicone based sealant

Another option is to seal the joint between the bathtub and the tile with a silicone based sealant.Gaps that are up to 30 mm in size must be pre-treated with polyurethane foam. Ideally, you need to buy a sanitary sealant to prevent mold from forming in the bathroom.

The stages of sealing with a sealant are as follows:

  • The surface of the bath and the tiles that adjoin the joint should be well degreased with a solvent.

  • To prevent contamination of tiles and bathroom, cover the desired areas with masking (paper) tape.
  • Punch a hole in the tube, attach the supplied tip.
  • Attach tube to gun and apply sealant to joint.
  • Fill the area between the bathtub and the tile in one stroke, as it is impossible to apply additional layers on the hardened mass.
  • Prepare a brush and soap solution for the desired tire.

  • With a brush, which must first be moistened in the solution, run along the joint to give it a smooth surface. Your movements should be strictly directed. With chaotic strokes, you will get an uneven surface.

If no brush is available, a rubber spatula can be used. If not, you can level the seam with a spatula or a finger soaked in soapy water.

When the joint is dry, remove the paper tape. If you have not used tape, remove excess material with a damp cloth.

Please note, that you must take care of safety when carrying out work.

When working with solvent, during the preparation phase, the area must be well ventilated. Gloves and a mask will help protect yourself from the negative effects of chemical fumes and will help prevent damage to the skin if a corrosive substance gets on the body.

Curbs - ceramic, plastic, self-adhesive tape

When the seam between the bathroom and the tile is covered, take care of the beautiful design of the area between the plumbing and tiles. Most often, various types of borders are used for this purpose.

Plastic skirting board is quite popular, and it is quite reasonable. Relatively inexpensive products are very simple and convenient to use for sealing the joint between the bathroom and the tile. Consumers are offered different models to choose from.

The most common design is one that closes the bathroom joint and is attached with liquid nails.

To create a corner for the joint, the skirting board must be cut at an angle of 45 degrees or use special fittings for this. A prerequisite for long-term use is the abandonment of abrasive agents and aggressive chemicals. Since the second option is rarely used, the joint is sealed at the same time when laying the tiles. First you need to install the skirting board - one side is on the edge of the bathroom, and the other needs to be drowned in the adhesive.

At the end, a tile is attached.

Covering the joint between the bathroom and the tile with a ceramic skirting board will be somewhat more expensive.

The advantages of this method are:

  • Increased use.
  • Resistance to chemical compounds.
  • The surface is hardly scratched.

  • The color of the skirting board will not change over time.

But there are also disadvantages, which include a small selection of colors and shades. The docking process is the same as for a plastic skirting board.

Life hack: it is convenient to cut ceramic products with a grinder with a diamond disc. If you use a fragmented disc, you can provoke a chipping of the edges and a deterioration in the appearance of the joint.

The easiest way is to seal the joint with self-adhesive tape.

The work sequence is as follows:

  • Thoroughly clean and degrease the tile and bath surfaces.
  • Remove the protective tape from the tape.
  • Heat the product slightly with a hairdryer.
  • Close the gap simply by pressing down on the tape.

Done! This method is the simplest and relatively inexpensive.

Conclusion

With strict observance of all the recommendations, you will be able to seal the joint with high quality and without damage, and provide a beautiful interior for the bathroom.

.