What to do if the socket falls out of the wall

What to do if the socket falls out of the wall The socket fell out of the wall - how to fix it yourself. Are there people who want to live without the comfort of modern life with a lot of technology and electrical appliances for every taste and color? But few of the devices are ways to work without the use of electricity, maybe only those that are outdated or have a mechanical structure. Ideally, all household devices should have outlets, but in practice this is rarely the case.

Yes, there are never too many outlets.

General

Many people cannot afford to make expensive repairs and change all wiring and sockets at once, so almost everyone has cheap Chinese tees.

One trouble is replaced by another - due to the heavy load of the tee, an excessive load occurs. Unable to support the weight, the rosette begins to fall out from the wall, and such a misfortune is familiar to many people. There is another reason - metal boxes installed back in the days of the USSR. The fastener spacers slide over the metal base and this creates a clamping effect.

Otherwise, there is no box at all, and the sliding occurs on the concrete wall in the seat.

As soon as you pull the plug, the socket falls out. If you pull out such an outlet and at the same time do not hold it with your other hand, then it will very quickly loosen and fall out of the walls in the near future. This is why most people are wondering how to reinforce rosettes that fall out of the wall.

Before starting the repair of the socket, which is constantly falling out, it is imperative to disconnect the power from the terminal board, since you can start disassembling the case only when there is no voltage in the network.

Several ways to repair

We suggest you consider a classic situation when a rosette begins to fall out of a concrete wall.

First, you need to understand why the fastening mechanism, which is presented in the form of sliding legs, cannot hold the body in the bore. Make sure that there is a socket in the wall, which is required so that the sockets or switch for the light do not fall out.

According to modern standards, they are made of plastic, with corrugated walls, which were specially made so that the legs could catch on. Old glasses made of metal have internal edges that are flat, and because of this, it is not possible to perform a high-quality installation of the outlet. There are also situations when such a glass is not installed at all, and the rosette falls out due to the fact that the petals do not expand very well in concrete.

Be that as it may, if the case constantly falls out of the glass, then we advise you to install a newer model of the socket outlet, which has corrugated walls, which will solve all problems.

If you find that a normal plastic socket is installed in the wall, then the structure is still loose, we suggest you check the legs.There is a possibility that the diameter of the mounting box is much larger than the diameter of the spacing of the legs, because of which the body simply cannot cling to the walls and will begin to fall out.

In this case, the problem can be solved in the following ways:

  1. Place rubber shims under the place of the foot stop to compensate for the void ..

    .

  2. Use pliers to bend the petals to increase the spreader diameter. Here you should immediately take into account that if the metal is soft, then it may not be possible to correct the situation with the petals, since during the expansion they will bend back. But this happens very rarely and only because the product is of extremely poor quality.

What to do if the socket falls out of the wall? Such a banal situation takes place if a mistake was made during the installation of the outlet, when the installer forgets that the petals should be properly diluted, as well as special screws should be tightened.

In this case, to strengthen the loose housing, you should perform the correct fastening with one screwdriver, as shown in the photo below:

If you live in a panel-type house, and the apartment has old electrical wiring, then often the outlet switches will be bad stick to the wall and begin to fall out, since they are installed only in a through hole and without a socket in the partition. The situation is clearly shown in the photo below.

In this case, you should first install the socket box, cut it a little if necessary (in some cases, there are problems with the thickness and the glass needs to be shortened from the bottom side) and only then reattach the outlet or turn it off to the concrete wall.

The second situation may be associated with a plasterboard wall, when the socket broke out of the plasterboard plane along with a piece of plaster, and then it will not be possible to fix everything according to the instructions presented above. This is due to the fact that the principle of fixing the socket in concrete and drywall sheet is different.

In the latter case, the plastic cup will be attached to the drywall using the presser feet.

To prevent the rosette from wobbling and falling out, a piece of drywall should be glued in place using plaster or alabaster. When the solution hardens, you will need to cut a small strip from a sheet of drywall, and then place it under the damaged area and scroll with self-tapping screws. This option with strengthening the wall can save the situation. An alternative method would be to cram newspaper into the voids around the circumference of the hole and fill everything with plaster putty.

Do not forget to also bring the wires into the socket before starting the process.

The mounting box should be pressed into the mortar so that it is flush with the wall surface (i.e., does not protrude), and then remove the excess mortar and wait until the gypsum mixture hardens. If the case is loose, the problem can be solved as shown in the video tutorial.

How to protect yourself and prevent such breakdowns

The main reason why the socket starts to loose and falls out of the wall is improper use of products. We have already mentioned more than once that you should not pull out the included cord in any case, since this can tear out the socket housing. No matter how they say, this is really one of the most common causes of a malfunction. For the rest, you should check the electrical wiring, check the reliability of the installation of sockets and switches, as well as the quality of the connection of wires and terminals.

.